How Can You Locate Spurs and IMD in Downconversion Systems?

Your downconversion system is live, but the spectrum is a mess of spurs and IMD. This ruins performance. I'll show you a fast, step-by-step method to fix it.

Start by disconnecting the RF input. If spurs vanish, check the LNA or add an attenuator. If they persist, inspect the LO and power supply for ripple. If all else fails, the problem is likely LO signal crosstalk, which can be verified with absorbing material.

Finding the root cause of these unwanted signals can feel like searching for a needle in a haystack. But with a logical process, you can systematically eliminate possibilities and pinpoint the exact problem. Let's break down the first step, which is often the most revealing.

Is Your LNA Overloading the Mixer?

You suspect the front-end is the problem, but how can you be sure? A saturated mixer creates a cascade of issues.¹ Here's a simple test to confirm it.

Disconnect the RF input from your mixer. If the spurs and IMD disappear from the spectrum analyzer, the issue originates before the mixer. The LNA is either generating noise or its output power is too high, causing saturation. Add an external attenuator to verify.

In my experience as a Field Application Engineer (FAE), the front-end is the first place to look. When a mixer receives too much power, it stops behaving linearly². This is called saturation or compression. Instead of just mixing your RF and LO signals cleanly, it starts generating a host of unwanted new signals. These are the intermodulation distortion (IMD) products³ and spurs that clutter your spectrum and degrade your system's performance. A common cause is the Low Noise Amplifier (LNA) placed right before the mixer. The LNA's job is to boost weak signals, but it can easily overload the mixer if its gain is too high or the input signal is stronger than expected.

A Simple Diagnostic Test

The first thing I always do is disconnect the RF cable from the mixer's input port and terminate it properly. Then, I look at the spectrum analyzer displaying the mixer's output. If the spurs and IMD are gone, the problem is coming from your upstream components. To confirm this, I reconnect everything but add a fixed attenuator, like 3 dB or 6 dB, between the LNA and the mixer. This reduces the power level. If the IMD products decrease by much more than the attenuation value⁴, you've proven the mixer was being driven into compression.

Understanding the Impact

This test helps you quickly isolate the problem to the front-end of your system. Here’s a quick reference table for this process.

Once you confirm this, the solution is to either reduce the LNA gain or choose a mixer with a higher 1dB compression point (P1dB) and a better third-order intercept point (IP3)⁵ to handle the power.

Could Your Power Supply or LO Be the Source of Spurs?

You've ruled out the input stage, but the spurs remain. This points to internal issues. The power supply or the Local Oscillator might be injecting noise directly into your system.

If spurs persist after disconnecting the RF input, the cause is likely the Local Oscillator (LO) or the power supply. Use a signal analyzer to measure the power supply ripple. Check if the ripple's frequency matches the frequency difference between your carrier and the unwanted spur.

If the spurs are still there with the RF input disconnected, the problem is being generated within or around the mixer itself. The two most common culprits are the power supply and the Local Oscillator (LO). Active components like mixers need perfectly clean DC power to operate correctly. Any noise or ripple on the power supply lines can act like a tiny signal, modulating the LO signal inside the mixer. This creates unwanted sidebands, which we see as spurs on the spectrum analyzer. I often see this with switching power supplies. They are very efficient but can introduce noise if not designed with adequate filtering⁶ for sensitive RF applications.

How to Find the Noise Source

The test for this is straightforward. Use a signal analyzer or a good oscilloscope with an FFT function to look at the DC voltage rail that powers the mixer. For example, let's say your Intermediate Frequency (IF) is at 140 MHz and you see a strange spur at 140.05 MHz. The frequency difference between your desired signal and the spur is 50 kHz. If you then measure the DC power line and discover a significant 50 kHz ripple, you have found your problem. The power supply noise is mixing with your LO and showing up at the IF.

Don't Forget the LO

The LO itself can also be the source. A poor-quality LO signal may have its own spurs or cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits⁷. cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits⁸ cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

What If the Problem Is Invisible Signal Crosstalk?

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits⁹ cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.

The Right Way vs. A Quick Test

The permanent solution to crosstalk is good engineering design from the beginning. This means a carefully planned PCB layout with solid ground planes, physical separation between high-power and low-power sections, and using metal shields or individual cavities to isolate components. At Safari Microwave, our 30 years of engineering experience are focused on designing high-isolation components, like our power dividers and RF switches, to prevent these issues internally. For instance, our SP8T switches and 128-way power dividers are designed with excellent isolation to ensure signal integrity.

But how do you prove crosstalk is the problem in a system that is already built? Here is a simple trick I use on customer sites. I take a small piece of microwave absorbing material¹⁰ and gently press it onto the metal lid or housing directly over the LO circuitry. This flexible, lossy material disrupts the electromagnetic fields and can break up a resonant condition that might be amplifying the leakage. If you see the troublesome spurs drop in amplitude on your spectrum analyzer, you have confirmed that LO crosstalk is your problem. This tells you that you need to improve the shielding or grounding in that area.

საბოლოო შედეგი

Systematically checking the input, power supply, and for crosstalk will help you quickly find and fix spur and IMD issues in your downconversion system.